Call: +48 22 266 25 58
Wiśniowski winter promotion: garage doors with openers up to −25%, fences and doors up to −15%, orders by 31 DecemberGarage doors up to −25% · until 31 DecemberDetails ›
Home › Blog › Fence height: front, sides, back and the rules
Choosing

Fence height: front, sides, back and the regulations

6 October 2025 · updated 6 October 2026 · 4 min read · Ogrodzenia ISS

Along the street, most often 1.4–1.8 m; by a terrace on the neighbour’s side, 1.8–2.0 m; at the back of the plot, lower. Fence height is measured from ground level to the highest point, including posts and caps; above 2.20 m a notification (zgłoszenie) to the county office (starostwo) is required. Below, how to choose the height for each section and what the local zoning plan may restrict.

Along the street

A front fence is visible from the street, and it is what ‘speaks’ for the house. The most popular heights are 1.4–1.8 m: enough to give a sense of an enclosed property without feeling like a wall. Houses with large areas of glazing are better suited to a lower fence or one with gaps; for houses close to a busy street, taller and more solid panels are the more common choice.

Between plots

On the boundary with your neighbour, what matters most is the terrace and the part of the garden you actually use. There it is better to go higher (1.8–2.0 m), solid or with small gaps. On the other stretches, e.g. along the driveway or further back on the plot, a lower fence with gaps is usually enough. Varying it like this keeps the cost down and looks natural.

Under the Construction Law (Prawo budowlane), a fence higher than 2.20 m requires a notification to the county office, wherever it stands. A lower one needs neither a permit nor a notification, but the local zoning plan may impose its own restrictions (e.g. a maximum height or a ban on solid fences at the front). Height is measured from ground level to the highest point, including posts and caps. Before deciding on a very tall or solid fence, look at the plan or ask the municipality.

Back of the plot

The rear boundary often borders a field, woodland or a property you don’t see day to day. A simpler, lower fence is usually enough here: the point is to mark the boundary and keep the dog in. What you save at the back goes towards the front, which people actually see.

Height and panel design

A tall fence with solid infill behaves differently from a tall one with gaps. Horizontal slats with a 2–3 cm gap give privacy from street level but don’t ‘close in’ the garden. With solid infill, wind load comes into play: the posts and foundations (at least down to the frost line, 1.0 m for Piaseczno) have to be designed for it. That is why the height is decided together with the design.

Dividing the plot into sections

Before the site survey, walk the whole plot boundary and divide it into sections: front, sides, back. For each one, note what the fence has to do: screen the terrace, mark the boundary, keep the dog in, show off the house from the street. That list gives you the height and design of each section, and from the street the whole thing looks like one design in one colour and style.

Pedestrian gate and driveway gate height

Most often the driveway and pedestrian gates line up with the top edge of the panels, which gives a calm, uniform frontage. There are situations where it is better to make them stand out: slightly taller gate posts (with lighting or caps) emphasise the entrance, and a pedestrian gate a touch lower than the panels can be more practical on sloping ground. The differences must be deliberate and consistent: one ‘step’ at the entrance looks designed, several random ones look like a mistake. Remember that taller gate posts with caps count towards the total fence height when you check it against the 2.20 m threshold.

With a sliding gate, remember the counterbalance section: the cantilever leaf slides out along the panels and should be the same height as them, otherwise when it opens you see an uneven, ‘jagged’ top edge. The heights of the panels, driveway gate and pedestrian gate need to be set on one drawing, taking the slope of the ground into account.

Frequently asked questions

Is 1.5 m high enough along the street?

For most houses, yes: it gives a clear property boundary and looks good with simple, modern architecture. If you want to stop passers-by looking in, consider 1.7–1.8 m or denser slats.

Does the height include the plinth?

Yes. Fence height is measured from ground level to the highest point, including the plinth, posts and caps. It is this total height that counts for a limit in the local zoning plan and for the 2.20 m notification threshold.

Can I have different heights on one plot?

Yes, that is normal practice: higher by the terrace and at the front, lower at the back and along the driveway. Changes in height should fall at the posts rather than halfway along a panel.

Sources

Legal position as of October 2026. General information, not legal advice.

Quote after a site survey

We’ll come out for a site survey and prepare a quote within 7 working days of it. There is a charge for the site survey because it covers travel, measurements including levels, and choosing the system; the cost is agreed individually and deducted from your order. Manufacturer’s warranty – Wiśniowski fences come with an anti-corrosion warranty of up to 10 years. The terms of our own installation warranty are set out in the quotation.

Request a quote