Safe gate automation: photocells, warning light, safety edges
A sliding gate leaf weighs several hundred kilograms, and the motor pushes with a force no child could stop. That is why a motorised gate has several safety features: obstruction detection, photocells, a warning light and sometimes a safety edge. Below: what each one does, which are required, what the installer sets up and how to check them yourself.
Obstruction detection
Every modern gate motor has electronic obstruction detection: when the leaf meets an obstacle, it stops and reverses. This is the basic safeguard, but it only reacts after contact with the leaf, so it is no substitute for photocells. The installer sets the force and sensitivity during commissioning. Do not change the force settings. Adjustment with force measurement is a job for a service technician.
Photocells
A pair of photocells across the entrance creates an invisible beam; when something breaks it (a child, a bike, a car), the gate will not close, or it stops and reverses. With automatic closing, photocells are required by the PN-EN 12453 standard. On a sliding gate they are fitted on both sides of the opening, usually 40–60 cm above the driveway, and often at two heights if there are small children or a dog. A double swing gate needs a second pair on the inside, because the leaves open into the property.
Warning light
It flashes while the gate is moving, so pedestrians and drivers on the road can see that the leaf is in motion before a car pulls out behind it. It is mounted on a gate post where it can be seen from both sides, and where the entrance opens directly onto the street, positioned so that it is visible from the carriageway.
Safety edge
A safety edge (a rubber profile with a sensor) on the closing edge of the leaf stops the gate at a light touch, before the motor ‘feels’ any resistance. On sliding gates, guards on the catcher post and on the counterweight also matter, so that there is no crushing gap between the leaf and the post. This detail is what sets careful installation apart from a rushed job.
What the installer sets up during commissioning
- Force and sensitivity of obstruction detection to suit the weight of the leaf, with force measurement.
- Slowdown before the end of travel, so that the gate does not slam into the post.
- Automatic closing time, only with working photocells.
- A test of all safety features: breaking the photocell beam, stopping at an obstacle, the warning light.
When the automation is handed over, you should receive the motor’s user manual and a declaration of conformity, and the force measurement should be documented. If you have a motorised gate without photocells or a warning light, adding them to the existing control unit is usually straightforward: a cable and programming an input on the control unit.
Safe habits at home
Technical safeguards are the foundation, but habits count too. Children should not dart through a moving gate or try to race it. Keep the remote out of reach of small children, because it is easy to open the gate from the house by accident. Open the gate for guests and couriers only when they are standing in front of it, not in advance ‘just in case’.
On most motors, the control unit can be switched to pedestrian mode: the sliding gate opens partially, just wide enough to walk through. Pedestrians don’t have to wait for it to open fully, and the gate is closed again sooner. You’ll find a description of motors and controls on our driveway gates page.
Frequently asked questions
How often should I test the safety features?
Every few months: while the gate is closing, break the photocell beam with your hand or a piece of cardboard – the gate must stop or reverse. Also check that the light flashes every time the gate moves and that the emergency key release works without forcing.
What about the gate during a storm or a power surge?
Motors have basic protection, but a surge protector in the consumer unit is an inexpensive extra you need to ask your electrician for. After a storm, check that the gate responds to the remote and that the photocell LEDs are lit. A surge can damage the electronics in the control unit and photocells.
Quote after a site survey
We’ll come out for a site survey and prepare a quote within 7 working days of it. There is a charge for the site survey because it covers travel, measurements including levels, and choosing the system; the cost is agreed individually and deducted from your order. Manufacturer’s warranty – Wiśniowski fences come with an anti-corrosion warranty of up to 10 years. The terms of our own installation warranty are set out in the quotation.
Request a quote